This kit is for venting 4” stoves like The Dwarf 3kW, Dwarf 4kw, Salamander Hobbit, Navigator Cod & Sardine through a metal or rubber roof of a tiny house, shed or small cabin. If you have a shingle or tile roof, use the 4″ shingle roof kit instead.
Since every installation is a little bit different you will need additional single wall pipe and may need additional double-wall pipe to complete your installation. Use our flue parts calculator to help figure out how much extra pipe you need in addition to the kit. Code for residential installation says, “ 3 ft minimum from roof penetration and 2 ft minimum above highest point of anything within 10 ft.”
⚠ Warning: California Proposition 65
Use of this product can expose you to chemicals including soot, creosote, wood dust, and wood smoke containing carbon monoxide, which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
Jason & Hannah (verified owner) –
To anyone considering buying one of the stove installation kits from Tiny Wood Stove, do it! Worth every penny. We have done a home-designed, homemade wood stove installation before, in a sauna that we built, and it was a real pain to figure out and buy parts on our own. The kit from TWS eliminates most of the mental headache and all of the extra trips to the local hardware store to try and puzzle out a safe and watertight installation. We did the through-the-roof kit for a Fatsco Midget stove (4″ pipe), and it works great. Not a single drop of water has leaked through the silicone stove boot, despite having to install it over a couple of raised seams on the metal roof of our tiny house. This kit would also be good for a non-tiny house install, like a sauna, bedroom, garage, greenhouse, or anything else. Only room for improvement might be a more detailed explanation of the installation sketch, which is adequate, but left a little to the imagination for our job – and after building a tiny house, our brains didn’t want to do any more figuring.
Thank you, TWS, for a very helpful and solid kit.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Michael Edwards (verified owner) –
My cabin is finished. The flue (4”) starting at the telescopic section to the rain cap was purchased Tiny Wood Stove. I also do ornamental iron work and have my own blacksmith shop. Well pleased with the stove pipe, everything works great.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Jason Joy (verified owner) –
Which 4" stove did you install? Something Else
Tiny Wood Stove was incredibly helpful with our Bathhouse Project. Installation to my Chofu Woodfire water heater was easy. The team was quick to respond to my questions and were easy and flexible to work with substituting and adding parts to the kit that were or were not needed by my application. All parts were well wrapped, free of scratches and well made with high quality stainless steel. I will definitely be using them again in the future.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Lea & Andy –
Which 4" stove did you install? Dwarf 4kW
While cutting a hole in your roof can be a stressful experience, with this kit it couldn’t be any easier. It took us one afternoon from start to fire. Quality materials and exemplary customer service. Remember to do your math, draw it out, and then do it again! The drawings from the Tiny Wood Stove people were super helpful, but we newbies did end up messing the roof hole up a little – depending on your slope and thickness of roof, the hole in the ceiling and roof will be off-set!
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Question
Wayne –
Were are you located?
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Dan –
Hi Wayne-
Our shop is in Hayden, Idaho. If you’re in the area and want to stop by, be sure to let us know in advance since we don’t always keep regular hours.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal
Question
Chris Hancock –
Is there a component necessary between the top of the insulated pipe to the vent top cap? How’s it going shipping to Canada these days? I’m located on Vancouver island Canada in a town called Courtenay.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Watch Unwatch Flag for removal
Cody Hennigan –
Chris- The roof vent fits directly to the insulated pipe and is secured with a clamp. Shipping to Canada can be expensive but it is going well. Feel free to shoot us an email directly at Support@TinyWoodStove.com if you’d like more information on your shipping costs. Our online cart will also estimate your shipping at checkout.
Upvote if this was helpful (0) Downvote if this was not helpful (0) Flag for removal